Aimed at integrators and developers, the 20-86-5000 series is a small, high specification, POCSAG paging transmitter printed circuit board, inheriting all of the type approvals of the 20-86-9000 Call Point 发射机s range and the 20-86 series Pendant 发射机 range.
-
-
产品
- UHF PCB 发射机 (20-86-5000)
PCB 发射机s - UHF
20-86-5000
The 20-86-5000 is an extremely small, UHF POCSAG paging transmitter PCB powered by a standard CR2032 coin cell. The transmitter will operate for more than 5000 transmissions under normal conditions before needing to be replaced.
The transmitter is ideal for developers and integrators wishing to develop their own low power solution.
Using a POCSAG receiver the 20-86-5000, as with all paging transmitters, can also be used for any general remote control application, such as turning on lights, disabling alarms or switching machinery on or off.
Care is recommended in order to avoid static discharge which may damage the PCB during handling.
20-86 transmitters support up to 8 inputs, each of which can be programmed with up to a 35-character message. Programming can be either with a serial programming cable that can be purchased separately or pre-programmed when supplied. Once the operating frequency has been set the 20-86-5000 messages can be changed using configuration software with an optional programming lead.
Although the 20-86 is a low power transmitter, a direct line of sight transmission range of up to 200 metres can be expected. Transmit range within buildings is reduced, but still considerable having proven to be effective in some cases between floors and across buildings.
- 超高频操作
- 体积小、重量轻 & 离散
- Internal cell battery
- 具有成本效益的
- Ideal for short distance paging or telemetry applications
- Ideal for developers and integrators
- Capable of operating on existing in-house paging systems
- Simple 遥测 solution
规范
| 电力供应 | 3V, CR2032 button cell |
| 频率范围 | 440-470MHz - UHF |
| Frequency Selection | 通过软件 |
| 电池寿命 | 约. 5000 transmissions 约. 5年待机 |
| External 电力供应 | 3.7 to 18 Volts (via onboard regulator) 3 Volts (unregulated; external battery) |
| Power Consumption | Standby: <0.5µA Transmit: 26mA (no TX LED) |
| 传输能量 | 10mW |
| 信道间隔 | 25 khz, 12.5kHz，或者6.25千赫 |
| 调制 | FSK with NRZ data |
| 偏差 | ±4.5 khz,±2.3kHz，或±1.0赫兹 |
| 输入 | Eight; user programmable |
| 波特率 | 512, 1200, or 2400 |
| 消息格式 | POCSAG, Alphanumeric or Numeric |
| Transmit Duty Cycle | Up to 20%; Maximum 30 seconds on time |
| Configuration Application | Sacoto (Salcom Configuration Tool Software) |
| Received Indication Outputs | Two LED outputs; via 680Ω resistor |
| Transmit Indication Output | TX LED; via 680Ω resistor |
| Transmit Duty Cycle | Up to 20%; Maximum 30 seconds on time |
| Programming Cable | 20-51-0001 (USB) |
| 串行端口 | 9600 , N, 8, 1; RS232 |
| 天线 | External; connection via thru-hole pad or castellation |
| Environmental Protection | None, PCB must be housed in suitable enclosure |
| Operating Temperature | 10ºC to +55ºC (+14ºF to +131ºF) |
| 重量 | 6g含电池 |
| 板尺寸 | 55.5mm x 32.5mm x 6.5mm(长×宽×高) |
| 类型的审批 | CE, FCC and AS/NZS Pending |
-
信息
The 20-86-5000 is an extremely small, UHF POCSAG paging transmitter PCB powered by a standard CR2032 coin cell. The transmitter will operate for more than 5000 transmissions under normal conditions before needing to be replaced.
The transmitter is ideal for developers and integrators wishing to develop their own low power solution.
Using a POCSAG receiver the 20-86-5000, as with all paging transmitters, can also be used for any general remote control application, such as turning on lights, disabling alarms or switching machinery on or off.
Care is recommended in order to avoid static discharge which may damage the PCB during handling.
20-86 transmitters support up to 8 inputs, each of which can be programmed with up to a 35-character message. Programming can be either with a serial programming cable that can be purchased separately or pre-programmed when supplied. Once the operating frequency has been set the 20-86-5000 messages can be changed using configuration software with an optional programming lead.
Although the 20-86 is a low power transmitter, a direct line of sight transmission range of up to 200 metres can be expected. Transmit range within buildings is reduced, but still considerable having proven to be effective in some cases between floors and across buildings. -
Details
- 超高频操作
- 体积小、重量轻 & 离散
- Internal cell battery
- 具有成本效益的
- Ideal for short distance paging or telemetry applications
- Ideal for developers and integrators
- Capable of operating on existing in-house paging systems
- Simple 遥测 solution
-
规范
规范
电力供应 3V, CR2032 button cell 频率范围 440-470MHz - UHF
Frequency Selection 通过软件 电池寿命 约. 5000 transmissions
约. 5年待机
External 电力供应 3.7 to 18 Volts (via onboard regulator)
3 Volts (unregulated; external battery)Power Consumption Standby: <0.5µA
Transmit: 26mA (no TX LED)传输能量 10mW
信道间隔 25 khz, 12.5kHz，或者6.25千赫
调制 FSK with NRZ data
偏差 ±4.5 khz,±2.3kHz，或±1.0赫兹 输入 Eight; user programmable 波特率 512, 1200, or 2400 消息格式 POCSAG, Alphanumeric or Numeric Transmit Duty Cycle Up to 20%; Maximum 30 seconds on time Configuration Application Sacoto (Salcom Configuration Tool Software) Received Indication Outputs Two LED outputs; via 680Ω resistor Transmit Indication Output TX LED; via 680Ω resistor Transmit Duty Cycle Up to 20%; Maximum 30 seconds on time Programming Cable 20-51-0001 (USB) 串行端口 9600 , N, 8, 1; RS232 天线 External; connection via thru-hole pad or castellation Environmental Protection None, PCB must be housed in suitable enclosure Operating Temperature 10ºC to +55ºC (+14ºF to +131ºF) 重量 6g含电池 板尺寸 55.5mm x 32.5mm x 6.5mm(长×宽×高) 类型的审批 CE, FCC and AS/NZS Pending - 手册 & 下载